NumFall

6x6 number grid puzzle: how logic replaces guessing

Learn how to solve a 6x6 number grid puzzle without guessing, using row, column and box checks, candidate marks and pairs of cells.

In a 6×6 grid, a beginner spots an empty square in the fourth row, third column. Believing the square is easy to fill, the beginner writes a 4 in it. Soon afterward, the beginner sees that the same row already has a 4 near the right edge. The beginner made the mistake by checking only the empty square and the squares next to it, rather than the whole row.

The numbers one through six are used in the grid. Each number must appear exactly once in every row, every column, and every 2×3 box. A number that shows up more than once in any of those three groups is an error.

A Latin square is the name for this kind of arrangement. Leonhard Euler published a study of Latin squares in the 18th century. Puzzles with the same rules came later, but they rest on the same principle of avoiding repeats.

The rules are very strict, which makes a 6×6 grid an excellent place to practice logic. A solver can support each number placed with the numbers already in its row, column, and box, and can verify each move before writing it down.

Why a 6x6 grid rarely needs a guess

Going through each row, column, and box in turn often leads a solver to a cell that can hold only one number. One unit is checked at a time, starting with a row, then a column, and finally the 2×3 box that holds the cell. The numbers a unit already holds are removed as options for the cell.

Take a row that already holds four numbers: 1, 2, 5, and 6. The numbers 3 and 4 must go in the two cells left in that row. For either of those empty cells, a solver has two possible numbers to choose from. At this point the row by itself does not show which number belongs in which cell.

The column comes next. When that column already has a 4 in a lower row, the cell cannot be a 4, which leaves the 3 as the only number. The row needs one of each number, so the other empty cell in it takes the 4.

In a 6×6 grid, a second rule usually removes one of the two possibilities. Solvers who review all three units before writing a number seldom need to guess, and they can explain each number they enter.

Mark the candidates in each empty cell

When solvers write candidates, they put small numbers in the corner of every empty square. A number is listed as a candidate only if that number does not appear in the same row, column, or 2x3 box. For example, if a row already contains 1, 3 and 6, a column already contains 2, and the box already contains 5, the only candidate for that cell is 4. A square that has a single candidate must hold that number, so the number can be written immediately.

At the beginning most empty cells have two or three possible numbers. They stay marked like that till another placement eliminates one of their possibilities.

After each placement, the solver goes to the other empty cells in the same row, column and box and crosses out the number just placed. A cell that was left with two candidates may now have one and that cell becomes the next forced number.

Keep your notes up to date after each placement. Looking back at a cell, a solver can see which numbers were removed and which move removed them, which makes mistakes easy to spot. If you leave candidate lists unchanged, that is usually why a solver ends up putting the same number twice in a row.

Use pairs of cells to narrow the options

In a row with two empty squares that can only be 3 or 5, these two possibilities are called a pair. One square contains the 3 and the other contains the 5, but at the moment the solver does not know which is which.

The pair still gives information about the remaining cells in row. The 3 and the 5 are already used in those two cells, so no other empty cell in that row can hold either number. The solver marks 3 and 5 as impossible in every other cell of the row, and a cell that could earlier have been 3, 5 or 6 is left with only 6, which goes in. When the two cells sit in the same 2×3 box, the same method applies, and the other cells in that box lose the 3 and the 5 as options.

Solvers often find pairs only after they have marked candidates and updated them a few times. The Classic 6x6 set in NumFall on the App Store has 100 levels, and all of them can be solved by logic alone. Before placing any number on the next level, a solver can scan one row for two cells that share the same candidates.

  • 6x6 grid
  • number grid puzzles
  • logic puzzles
  • candidates
  • solving technique

FAQ

What are the rules of a 6x6 number grid puzzle?

The grid uses the numbers one to six. No repetition is allowed in a row, a column, or a 2 by 3 box, and each of them must contain every number exactly once.

Can you solve a 6x6 number grid puzzle without guessing?

Yes. Check the row, the column and the 2x3 box for each empty cell, and the only number that fits usually shows up. By checking the row, the column and the box for each empty spot, the only number that fits usually emerges, and each number that is put in has a clear justification.

How do you mark candidates in a number grid?

When solving, you write the tiny numbers you think could go in an empty cell in the corner. Those are the numbers missing from that cell's row, column, and box. Each time you put a number in a cell, you erase that number from the lists in the other empty cells of the same row, column, and box.

What is a pair in a number grid puzzle?

A pair consists of two empty cells in the same row or box that have exactly the same two possible numbers, like 3 and 5. Those two numbers are no longer possible in the other empty cells of that row or box, so solvers eliminate them from those cells.

Who first studied the grid arrangement behind these puzzles?

The arrangement is called a Latin square, and Leonhard Euler published a study of it in the 18th century.

Share this article

Know a puzzle fan who would like it? Send it their way.

← All articles